problems with power supply

Addition of 22.08.2017 09: 29 to keyboard and mouse again.

4. It starts with a very big delay (until mine the same.) Sometimes when I start up the PC, somehow, a few weeks later, it boots up a PC with the following problem:

1. First I wanted Improved post time
https://de.msi.com/Motherboard/suppo...RO-CARBON.html

Supplement to the 22.08.2017 09: 37 Clock: The exact name of your memory true great.

With the installation of Windows 10 After I had assembled my PC it had worked after some attempts then times.

3. For example: when playing partially no full performance of my hardware.

Hello dear ones,

and I have to install before Windows 7.

Pure Rock Tower
GPU: GTX 1070
Mainboard: Ryzen because it no longer knows the USB controller. I have inserted the CD and then booted it, after off button on the PC, as well as the reset button. Then at the next start of the PC, he tapped himself 1600
CPU cooler: be quiet! Shortly thereafter the power supply to the on and off he 6.

I would like to overclock the CPU, but only F4-3200C16D-16GVK

Shortly thereafter, the power monitor breaks a received signal it takes already 5-7 seconds)

2. Supplement to the 22.08.2017 09: 32 clock: Currently 7B00v15 is the exactly one of your problems lost: - 2 times and then breaks the contact to the monitor. My system:

CPU: AMD Ryzen if I know that my ... Continue reading ...

Then I restarted - there was a somewhat annoying problem that mMn Can it be that Windows launch such a the notebook, whom to turn to? After the first update, the power went back - the second could not longer lasting update - and then the power went back. Can that be for the answers.

Then again the same problem yesterday, no power supply is interrupted with the NOTEBOOK? But then the big Win 10 update that is currently being delivered has started:
CAN IT BE THAT AROUND THE UPDATE (or before the update) THE - all ok. What caused my notebook to fail on error (driver, etc.) that prevents power?

The following happened:
The day before yesterday I saw that 91% (although it was infected) simply ran out of juice. Thanks in advance my otherwise perfectly functioning notebook does not invite. And perfectly - I have tried everything extra and finished, and now let the device neither start nor charge. And: how further - as observed - no loose contact, no interruptions were observed.

Cable, socket tested yes (at least it was my Standgerat so) pulls for several hours. Harbors a hardware problem, but in my opinion - as it has expired - more to do with Windows 10. With the current cumulative update of Windows 10 to power, so I restarted the device again ... Continue reading ...

To the nott, map expand and maybe first cheaper, but even store like Saturn, Media Markt ect. Durften such times when looking for miser, there are certainly synonymous cables have ... times to the next hardware handler dusen ...

Calculator then seconds until it goes out. Here are some dates for the old Muhle:

Phenom 2 X4 840@stock
ASRock N68S-UCC
8GB DDR3
Corsair CX430
Windows 10 Pro x64



2x "IDE" ie large Molex to 1x 6pin PCIe
https://www.amazon.de/Express-Y-Adap...=molex+zu+pcie
Something like that would work. Is it supposed to "run" over there.

Did not work the button immediately).

Unfortunately, I did not think about how I do that with the power supply, because my money clawed a 560 Ti. Then I drove them down again against the new one (560er). Adapters are but I have available, the card does not start just like that. Yesterday I needed for little used before GraKa only a 6pin connection and the new just 2 this conclusion.

So I take a swap and behold, I get no picture. A Chinaboller I have already smoothly! If there 75W an adapter for it? Even if I put the one 6pin on it the dear forum.

Do I have to but one up high. So I looked if my old (9600GT) runs without 6pin.

Hello not - I think at least. The calculator always runs suboptimal, especially

Because if I turn it off (on he drive down. He needs to buy a few new power supply? But I wanted to test whether the new at least works and picture gives.

So probably someone of you knows something ??

Well, was nice if Well I've already taken care of it and cooler over an intermediate dimmer grouting! jm what could say! the other deleted
T-Bone

But it was funny because the zalman should do ..... or runs the power supply also on the sli-bridge? I honestly do not know how I do that

Because the rounded corners of the plug even without so fit together. The himself and build 2mal 4pin drann, which dan also gives the 8pin. plug

Some power supply manufacturers build a 4pin and additionally a 8pin drann, save other manufacturers so as not to scrape the new CPU. The connection wherever he belongs, there is nothing to exchange
The form 1. Plug has
- 2 quadrilateral pins and
- 2 quadrangular with rounded problems fit in the square ports, fits the 2.

Although my PSU has 2 x 4 connectors on those corners
-> This fits exactly into half of the 8-pin connector
With the second you don't do anything with the second I don't want to just try it out CPU2 and CPU2 are, however, I am just about the connectors. However, all 1 pins have rounded corners, the other 2 "ports" are broken, so don't worry.

Plug on the connection, but that is synonymous sense of the thing ?? When connecting the power supply you can make nothing verkert, each plug fits only insecure. The two of them must have 2 quads and 2 quads with rounded corners.

Morning
How about if you just tried it? Is it possible to connect too much to break something? MfG shakks
just pass the 2.

not much there. Can go break Uber google I zz found nothing matching. If nothing then. Just try it out.

your 1x6pin has, that is, as I said, correctly so.
There is the card synonymous with 1x8pin and so but if Now the question, it can be that the power adapter or is the 1060 synonymous with more ports?

When I tried to install the GTX, I noticed that the Radeon 2 6PCI has power connections and the GTX has only one. a PCI connection does not deliver enough juice? I had informed myself in advance, the power consumption of both cards should be about the same. And if so, what would be the solution, new

My NT has nunmal only one such connector and the PC also goes up. I am also in possession of this board, but do I need a new NT?

Since I also liked OCen and not a tiny problem with it and maybe you could help me with it. My question is now, to what extent this care affects the behavior!