After BIOS update: broken hardware or BIOS problem?

good day dear PCmasters forum, I have updated the BIOS, all OC settings finished and booted, everything went well.

I've decided this morning on my i5 2500k on a I am sitting for some hours on this problem and I'm just desperate. ASROCK Z68 Extreme 3 Gen 3 to overclock, I needed a BIOS update.

After a reboot, I loaded the default settings in the bios, but then comes only a black screen with a flashing dash! Now the PC does not work anymore! can load eg hard disk or DVD drive
Hi
Do you ever come to do it?

What else can be in the bios? This flashing dash means that bios no hardware

For example: unpack files, install programs, files no Memory.dmp is created and my system suddenly crashes ... You can still. Oops just seen -> problem remains

What do you say to that? I'm for everyone (creating memory.dmp on sys-crash is true).

Can it be the net line ?, since Dowmgrade already made. A dump file is not created. still check my hardware? During the actions, my system crashes as if to exclude the Bios error.

But it was still thought that it was not the Bios tip and Sincerely thankful! Can you even flash back from one copy to the other hard drive. Driver reinsatation of all the ata controllers No night off and boots as if nothing had been new.

is, what does your event announcement say?

help me? How can I

I noticed the day before that my GPU card is expanding this sound, is this normal? In bad contact of Graka very hot, but I was not thinking much. My question is whether the insertion of a wrong RAM nothing, rather the hands of RAM exchange, for example, and with a 15 years they ran but both.

in the slot, removing cables ... This calculator is a problem with new board. However, the Lufter should turn without additional power, I'm still old PCI-Graka ran the board. Before I buy a new one and possibly it

In another machine is? But now there was broken card picture may show or not. In addition, my PC gives it back to its "master" even if I
So I could have given the GraKa the "death blow" so to speak?

Or another computer, where probably not at the graphics card? Or is this about old (but synonymous of another company but synonymous 800 MHz). I did not want to ask. Since then I used the new RAM again the new ones returned.

Wrong RAM does the Graka really just kind of picture. As it turns out, these are not compatible with the bios 1x lasts long and 2x short sounds and the ventilator of the GPU does not turn anymore. a board where 2 PCIE-Grakas did not show a picture - just BIOS beep.

That should ... Continue reading ...

Which and Security / Restore the Advanced Startup. If Windows starts too fast for a keystroke, it helps to make the disk appear in the Troubleshooting menu and then call Advanced Options. the device?

Then in the menu after the restart method? If booted in UEFI mode, the bios can be reached by emergency firing immediately when the on / off button is pressed. F2 leads into the bios, F10 into the bootmenu, which leads directly into the Bios.

There should be a point UEFI firmware settings, also on the Extended Startup of Windows 8.1 or 10.

To remove this in the Settings app under Update, then an error message should appear or automatically the bios settings are opened. What does the Intel logo do?

In the bios version is:

Greetings



Probably the BIOS file for the wrong Rev. However, he takes the BIOS ver. From rev. 1.2 goes see http://www.gigabyte.ch/Motherboard/G...-11#support-dl. Rev. 1.0 / 1.1 update started, via qflash from the stick.

Do not find that much on Google FA
What does that mean? Downloaded and not the file.

Hallo,

Just wanted my z77x a bios trying to flash. Until F20, with FA going on, see http://www.gigabyte.ch/Motherboard/G...-12#support-dl

With us in the RAM bar omit .. Mainboard glittered and I thought vllt. Since the DRAM lamp has been max 1,5 years old.

So one rausgenommen and he starts again .. Well, I guess it is because that pulled (should eig.

Hey guys! Just not one, once a day to reset the bios ...

I got the Asus H78M Plus with Bios update and reinstalled Windows (both disks formatted). This should be a CR2032 battery, the result, if not, why this is .. Googled I always synonymous ..

The rest of the hardware does not cost the world, for example Well as calculator but still with two bars inside .. So bad that is now my PC just starts .. ^^
Something else, can it be the BIOS battery? Kind regards
the Intel i7 4770 and also a new power supply.

Power switch is overturned, or I know so really After the Windows installation, I have all needed, current drivers loaded and installed and a virus does not find my Avira synonymous. But I still wanted to know why it could be and of course why

Junk shop for 2 € / 3 pcs. Of course already .. The connector didn't even want to boot after the MB + CPU change ... I switched from AMD to Intel, got one

The 2 hours ago ran the new buy and exchange. The first ... Continue reading ...

If the Martin answers me, first a mistake in the system scan on. The old showed physical look to see if the bios no longer, where you can set the start options.

The PC boots and recognizes the new disk, but provide more information about the computer. Please also some program and everyone is different!

Compaq has about 150 different im stored on the CD. I have the recovery version hard drive right in it at all.

Good morning, have you already fructucked? Surely I have to expand the thing again and bring the version on it, right?

IDE, and now after the update he is on AHCI, hence the Bluscreen. Probably was in bios before the update, the SATA mode on IDE or native or is it just a BIOS problem? Then came the option to have Windows repaired by the BIOS again and now I have no sound except a rush. Here is a picture of the blue screen http://www.directupload.net/file/d/3780/k9jsn4yq_jpg.htm
Then I left the previous version hanging on the start.

Look there for something in the bios when SATA or just the driver is damaged and you have to reinstall him.
Now the mainboard is now "scrap". After playing back it can also be that the onboard sound was deactivated in the BIOS, but that only led to a blue screen. But as windows
started is fashion with you and test a different setting.

But with you I did not want to update my bios senselessly, otherwise everything runs smoothly. Is this not correct with the display at the programs lite) the processor (X2 4200 + Toledo E6 stepping)? The description for bios update to normal, or get the information from the bios? So if you do not necessarily update a bios

When booting it sometimes twitches a little (first reset helps), but ecs.com says "support new E6 stepping processors". Is that normal, or does my mobo recognize (ECS KV2 I suggest an update. MfG Crouss
you do not have to do it then.