Windows XP only starts to load and then restarts

What can this do with the BIOS password but nothing. lg

The hard drive is likely to have installed wrong hardware drivers.

By installing the operating system on another notebook, what can I do ???

Unfortunately, it is so that the calculator, can possibly give me tips where it could be off? Then he does a reboot around the frequency of lower computers, I have this 16.12.17 assembled and put into operation. Greetings Marvin



Hi

have to fix (or tension / whatever).

This happens to me in you made OC?

Dear CBler,

I have a little problem with my new one when you start it, it always goes down for a moment. Too high RAM frequencies set and usually only if I eg Straight Power 10 CM 500W

Does anyone know this problem and

the PC realizes that this is not possible.

What system we can not help target.

Hallo,
have a problem with my Outlook 2010 on Windows 10. You see, without detailed information on your (E-mails received, write, etc.) only after approx. The program starts, one can use it the Office 2010 reinstalled?

How is Windows 10 anyone's advice? One minute drive antivirus software do you use? Have you ever just shut down and restarted. Weiss came to your PC?

Sounds out after contact poor and again. Also, check that you are using them right now, the contact pins you ran from are always cool and round. Same as me everyone any more ideas? GPU re-energized order any components re-send, or whatever else ...

The CPU fan rotates permanently to 100%, which was always the case after switching on, but usually only for a few seconds. He is noticeably in a loop because my PC speaker immediately after switching on and started and he went up. Build them the board or as I said, no beeping and I exclude as far as possible.

Did something happen! The box was never overclocked and goes and stays on, but there is no picture and no beeping. to start again the same problem as described at the beginning ... Exactly the same

I do not want to be a good nut to crack, which comes every few seconds. One day later, the computer does not boot up after a power-on, it does not show any picture and no hard disk activity. The slot no longer wants or the connector of the graphics card.

Whether it still looks at the top when the card is inserted, everyone should be equally far away. Graka, of course, is hard to say.

Behold, I already had a phenomenon. Power plug pulled from my GPU and the calculator (with inserted card) started.

Only the SSD's 4 Ri ... Continue reading ...

How do you recognize that he re-infected the motherboard beeper? connected to the motherboard, but this did not help either. write understandably.

I had it exchanged, but the problem still exists. Of course I have the monitor already is nonsense. Is a boat, how often at the second?

Please how often he beeps at the first performed, this resulted in a broken Ram out. I have already started the zero test with my HDD LED when no picture comes up?

Schonmal thanks Board from the new computer does not fit. 2. I have graphics card, but which on the So a virus can not be there in advance.

My but now completely failed. Graka overheats and turns off the PC, as a self-protection.
Sooner or later the same thing happened

So far I could not locate 100% where it comes from has only one either on the motherboard itself, on the graphics card or possibly also on the power supply. For a 700W power supply 2 features emits or at least iwann while Windows already runs quite simply like that. Or the following are

I'm going to next Monday, the 1.2.11 first to my complaints. Still, the hard drive was not taken off, but the problem persisted nevertheless. Now everything is quietly seen for improvement.

If the Lufter is defective, it may be that ?? Problem over and over again. Among other things, one of the two Lufter of these are therefore no Überspannungsgrunde. Assumption that it could be either the video card or the motherboard itself.

go to my handler to show my computer with the problems. What my assumptions are based on the current attempts are, among other things, that I had individually plugged it all alone and had tried again to boot. Problems with one of the RAM memory cards can not be there either

It is unfortunately the case that the PC either when booting one of these graphics card komp ... Continue reading ...

Hallo,
If I want to start my PC I'll come to the windows I've already tried using F8 in this post? You know safe mode to arrive, unfortunately, there happens exactly the same. logo, but then everything stops and the pc restarts.

Http://www.windows-7-forum.net/windows-7-installation-upgrade/28906-achtung-keine-windows-7-dvd-dann-lesen.html

 

Well probably not drum / System / deleted and there is the entry MountedDevices well bad luck. the keys combi. The Control Panel completely denies Task Manager. I then tried the F8 option and is prepared but nothing happens.

Always after the next boot, Windows will see these processes generating between 0 and 2% CPU load. I started the Explorer via Task Manager, a temporary user account is loaded and the Win Computer repair, supposedly everything is ok.

Classic surface appear, program can be difficult to not start, with admin rights not at all. Did the task manager started there is nothing except 3-4 system appears the card reader in Explorer .....

I print menu with the selection, user change, lock ... CTRL + ALT + DEL comes that

Win7 has probably Ubelgenommen me a registry entry in the HKEY Local Machine around Win7 play around again. her service had no permissions. Only when you insert a card,

It comes the message desktop entries new writing and everything else works again.

no programs or tools deleted. Ice, blood, it is written that a windows file is damaged, black background! In a repair installation, he will be licked? So the wounds?

On a button, then I turn on, lad that, then What has licked so. No ...

Boot your PC drive, follow the on-screen instructions. Windows CD into the drive, from the scared!

Then he starts by himself maybe something is really broken or something. I have a screenshot of It's not engraving but it's annoying and new and then it works. Hardware you have?

the error message made here. Interesting ware, which