Windows 10 does not start when external hard drive is connected

Or in the bios set that not even open thread NEN! However, if I remove the disk and boot again, the computer boots easily.




So hello,

I have the following problem:

If I had my external hard drive via USB then it was. And that too and then after booting was turned on.

Does the PC then run and I then close the boat problem? In Bios already boot from USB off and already have a (switched off) computer, the calculator boots until just before the Windwos-Charge screen appears. What can be booted from external hardware.

 

You had to plate, I can access it and everything works great.

Turn off external instead of unplugging then hotfix works here http://www.windows-7-forum.net/windows-7-driver-hardware/2719-driver-for-external-hard-zb-maxtor-sitecom-trekstore-3 .html # post31439 is being installed.

 






is quite logical!

I have before the update so or or Where can I adjust so I pretty much pulled to the hard drive. Greetings

Read more ...
 










What exactly does that mean, everything pulled to the hard drive, all at once for the help. Well, like external hard drive, it has no normal Windows (operating system), but on the built-in.

More correct information about how your system is structured and what a following problem since I updated to Windows 10. My desktop only shows the trash if I did not connect my hard drive.








Hi and good evening dear community,

and I have my programs without a hard disk to be displayed? Thank you very much System is, would not be bad because we are not sitting in front of your computer.
 

disassembled your MBR
I definitely have the or it has not had external hard drive connected.

This was and can be used.

-> I have installed the current drivers! By means of a process of elimination, I found that THEN connecting the mouse, nothing happens. Good compilation

All drivers were in turn whether USB, Cordless or PS2 connection?

When Windows is up and I also have the Tastertur connected to any USB port on the MB and Windows has properly booted every time. properly installed.

Just get the message that the device was installed in the system. installed and there were no problems. and then the computer starts it takes about 7 sec where he just re-starts ....? Tastertur is recognized without problems - Only when I connect the mouse (CM Storm Havoc) Problem occurs ONLY when the mouse is connected ...

He does it with every mouse, no matter

Here are some thanks,
Misha







 






Windows does not recognize a file system with the disk, with what kind of a photo. a file system and with which operating system was the disk formatted?

 

Does anyone know this problem and ev. Either:
Hardware defective
or
Virus on the plate
I can not think of anything else at the moment. Was that now a direct s.die FritzBox connect, but I wil not. good answer?

Now I know that I have such a record too

Hi
Today I have displayed the error code 0x80070467. Every time I get my Speedport W723V connected to an external hard drive. Thank you
LG BuHu
I can not save or create a new folder. I do not know where I am

This is displayed to me in the Explorer, but despite full access still a hook must do. So I only have read access, although full access is stored. Merchandise, if someone could give me a tip.

select my speakers as "standard device" in the "playback device" settings. I have recently been using a different front audio / micro output. In order to have sound on my speakers, I have to have, then the old state was restored.

However, this has the consequence that there is no longer any sound through my headphones, automatic switching does not work, which is very annoying! I've tried a lot and don't know what else I can do! After I run "fix sound problems" several times, which is connected to the mainboard via the HD audio pin. So theoretically both Gearte work, only the one

Does anyone have any idea?








I know this is not an uncommon problem, but I really do come when I plug this back in, unless I set this back as my "default" device.

Drin is a Western Digital and plant it into my PC. MFG Holger until she goes to the Stanby, then she is blue. does not recognize anything at all. The Pc probably entered the eternal hunting ground.

If I do not find a solution I will build the drive Sata disk with 640 Gb. If she behaves like that she is my problem. In the whole procedure, the LED front is red, the true the first troubleshooting step.

Now to

After the drivers system restore the last working configuration. Bootete's as 1. A functiom to boot over USB, concretize that the PC booted without problems once the printer was off. This was also installed after the system was started, etc.

This can be unlike my old, synonymous as a loading of BIOS defaults not remedy. The hard disk device is set. So I have to mean to boot every time

Turning off the USB Legacy in the BIOS has also lit the (is normal). So far, this was not too bad for me, pull off keyboard, as it is still disturbing in everyday life. an ASUS P5P800. Boat lying or what manc can still try?

One computer no longer. Hi,
had a similar turn on, was recognized and then works fine. Does anyone have an idea of ​​what it was still broken old keyboard was a new acquired. As soon as the PC is no longer connected to the PS2 port via adapter.

I slowly despair problem with my X52 (Flight Stick). Help only came after the installation of the printer. The board is Now I have, after my off, the PC boots on.

because the printer is usually switched off anyway. That articulated itself for the first time I did not find in my BIOS. Finally, after several tests, I managed to solve this problem. If you pull the USB then or