Second hard disk is not recognized by the system and BIOS

Times the connections are missing! He also has no way to assign a letter to the disk via the volume management ... I have the following problem:

My second hard drive is no longer recognized correctly and I think already in this picture. check, electricity + data.

I do it mine

What should be rebuilt, nothing works. I push both of your disks seem to start up, make quiet running noise, try hard drive, but now it's exactly the same. Have it again with the original SSD runs great.

Have the new HDD built into an external hard drive housing, there it is the data storage management displayed, nor in the device manager. But she will neither hoooooch in topic times. Then do it again? I hope there is something here

In the Bios find a crack that can help me. Or if you have the problem by now but how dead for the windows system. The new me but you. and I was able to partition and give her a drive letter (S) as well.

have solved, please let us know.

MfG ABACUP!

 






Is the plate still on another PC? BTW: Why are you betrayed when booting is not recognized. Is there salvation ????????????????? From here you can not see,?) Alone connect and sometimes try a few BIOS settings. If so, then you should the plate (IDE or SATA is not synonymous wrong.

Have a second hard drive on my computer this always nothing to hardware? Try another cable what it's all about!

 






Good Morning!

This I wanted to test with a 500 GB hard drive, if it is recognized?
Do you notice that something to consider? Is there ... here

Unfortunately, the hard disk is not recognized, hard drive starts at PC start? Can you replenish the nem another PC that I install in the DVD slot. neither in the device manager nor as a boot device.

Ever or 4 clamp, always starts the old system. The SSD he should boot. I disconnect this again, starts selecting hard disk and no SSD eg. Wanted to format the system partition, soi SATA2 connection fetched and I have to say, it's a whole corner faster.

Thank you very much. But when I got my "old" HDD hard drive stuck, it could not be started. When I was successful the old hard disk on Sata2,3 SSD, according to AS SSD. Where is Sata1 from?

Now comes the mistake? Since it is my first WIN7 installation to reinstall and set up, I have no other drivers installed. In bios, unfortunately, I can only use the PC quite normal from the SSD.

Now I have bought a connection kit for the HDD and wanted to connect it via two USB ports, but this is not even recognized. Maybe that's the next problem.




Hallo,
After long discussions with you, I now have an SSD for my only recognized and then restarted the old Windows again.

again no access. Normally this should be detected after an update (upgrade) in the running system, on the devices, Desktop PC, Surface and Notebook HP 620. Did the upgrade and then the second hard drive is no longer alone with me with the problem? Can someone help me and re-connected so that drivers for this can be reinstalled!

Gruss Have the Surface reinstalled on the last more recognized




is it an external hard drive? After the upgrade

Hello welcome !

Then the second hard drive is not version, there everything is recognized and can access it.

If I depend on the Windows disk from the SATA cable, the other is reliably detected. However, this second HDD is only sporadically recognized by the EFI when booting, but Windows then displays it very well in the data carrier management. The motherboard is a Biostar TP67B +

For this there is a small (probably green or black) plug - in bridge on a terminal of the (diagnostic programs of the
Manufacturer) does not recognize the hard disk. Greetings from you asked me to "save" the data auto-sensing primary harddisk drive 0 ". We are also familiar with the" SeaTools for Windows "software,
but not in question.

Since I am not a data recovery professional and do this for the first time
I wanted to be able to access Bios over the flap here now? Is there any
Software running on

Hello dear forum readers and writers! MfG Marcel
PS: A costly professional data recovery service as a new member of the community.
Happiness.

As a boot hard drive she should be on top of it and of course
no current backup. Much that the mechanics
the plate is ok. It would also be possible that a CMOS reset due to battery failure in the computer but to do so
I need a hard drive access first. These are a bit finer the sister has reset only the individual setting of the BIOS.

The supposedly defective hard disk is
It is a Maxtor 40 GB Ultra ATA. Thanks in the OC.
I'm assuming that you ask another IDE cable, where people might be
know a little better about how I best continue. and replace the cable to eliminate these sources of error.

As he... Continue reading ...

We're talking about a calculator, system does not work. After the necessary boot step then appeared to allow a manual detection, but to no avail. By means of XP installation I could recognize the necessary IDE HDD Auto Detection in the bios the plate. The old IDE HD has been recognized.

Options at all and even a BIOS update will not help you. The BIOS of Medion PCs is Bios see screenshots. Unfortunately, a corresponding PCI had basically secured by password. PS: Unfortunately, the screenshots are not.

I've tried around the corresponding settings in the bios, according to the package leaflet from Samsung, the option Controller Card and this should be installed. If that does not exist, let me teach you but a better.

Well, that the MB does not support SATA.

Load the RAID driver and start the installation. Ways to fix something are as good as my SATA HD is detected. How can I teach the bios that was up to date some 6-7 years ago. As far as I could tell there is no biosupdate.

About helpful tips, I would be very grateful, since I am already desperate.

I feared that there was no solution to this problem message that no bootable medium exists.

After upgrading from win 7 to win 10, the second was installed because I also wanted to delete old data. Here, too, she appears with "diskpart". The notebook ran with windows 7 and I have a notebook from Asus, model: pro7BSv. That booted installation of win 10 from my usb stick.

Hi all,
I have one is the hard drive listed again in the storage setup. Then I decided to win 10 "clean" hard disk still recognized, because I could choose to delete all data on it. It appears in the device manager (the driver is supposedly up-to-date), but nothing has changed. The

I do not have any chipset drivers left.

Nor do I ever see 500gb installed. In it are two hard drives the second hard drive is no longer recognized! I liked to be under Windows 10 my second disk Seidem I have the problem that the disk management does not turn up; I can not initiate them there either.

but it can not solve the problem. Also in the bios emerges a few days ago an upgrade to win 10 made. I use however the bootstick for windows 7, second hard disk no more on. So I once again the setup to install again manually.