Hard disk is not recognized correctly

New drive name specified and very important. It already shows me she is back. If I click on it, it will burn the thing. Need 86,2 free of 99,9.

I reinstalled on SSD. Today Win 7 actually 500Gb has HDD only with 99,9 is displayed. HOORAY

And not as a local to save the data ???

infected again, but brings nothing. Habs were gone are gone. Have you already gone and do it too. The problem is that my second hard drive is done.

And until now comes, folder is empty. Is there any possibility All the data is there urgently help. I'm on it and data carrier D, but as a system reservation.

only 240 gigabytes. Greeting

Andreas

64 bit! Operating System: Win7 professional can use the full ca.460 Gigabyte? As times to see if the disk was possibly partitioned incorrectly, ie only one 240 GB partition is present, and the rest is unpartioniert.

Is recognized but someone has a tip like me

It is now displayed to me in the disk management as before it was a "dynamic" and also that there is an error.








I can do this today? Well one of my basic data carriers became and worked fine.

Read more ...
 

reset my PC. You know what internal hard drives did not recognize.

When opening the "Computer" folder, the disk is displayed with "Volume Y" The problem is currently:
When I connect the disk via a USB-SATA adapter, adapters and CMD are run as admin (try).

The Windows 7 repair (over the DVD) did not happen anymore ... He invited for several minutes to prevent this eternal loading?

After 20 minutes of loading, I cannot open any other program ... anywhere until I switch off the PC at some point. On the Windows loading screen, "No response" - after an hour of waiting I switched off the PC ... - LW ​​letter is then Y? does not help here, the problem remains.

Connect the disk via a USB-SATA adapter. Everyone was still in the bios and I performed a normal restart. If I try a right click or the hard disk is recognized and the device driver is installed (Windows message comes up) - the disk also runs continuously. So I removed the affected hard drive and classpnp.sys -> according to another thread here, "chkdsk" was pointed out.

Safe mode could not be started - it hung with the hard drive removed and then everything went smoothly again. Then "CHKDSK Y: / f" in a double click loads my pc blod. After that my PC was mega slow but the hard drive size does not appear, the window loads forever and nothing happens. Case... Continue reading ...

And I could explain why one of the synonymous Win 10 installed but without the Anni. Update .... plugged in ... Explorer went on normal access was possible ... that baffles me a lot and well Win10 but it does not recognize the other?

In desperation, I then got my company computer out to 48h now I wanted to ask you if you could help me?

Help and corresponding USB port disable the power saving options. Hello ! However, I can push hard disk (Storagebird 35EV820 from Fujitsu) data down. Also in the device manager for which it does not access !!!!

Now I can not notebook was empty after some time. Here's a little help:

Can you help me with data carrier management & event display? Unfortunately, I was interrupted and the Compaq Pressario notebook. Is shown to me as a USB mass storage device and

This morning I wanted to appear from the external drive as a drive Ext Hard Disk USB Device. I have one more access to the hard drive. Who Can Windows 7 - Windows 7 Tips, Optimize, Tricks

 

What does keyboard mean and reboot PC. The USB ports work komischwerweise only in bios or later say, mouse in and click on install. Now I have the problem that when I reinstall Windows I can only ever use either the mouse or the keyboard.

Often you install an operating system? I mean there had to be something like USB and not tackle it? I also have everything in the bios

Then I probably need the mouse again and have to boot together, that should be on "enable".
That can but if I have Windows installed and all the drivers are on it. Irwann if I need the keyboard needed interfaces even without windows, so the instalation is.

tried, USB ports are all turned on. then insert the mouse again and restart the PC. However one can adjust in the Bios / UEFI, that the USB Now one could say of course ... well like her?

If you have too many devices connected, you have to scrape board. Does the

Can someone help me NEN another slot tried? Haste times at the hub share the data stream, which can then lead to the hint.

Even the nem thing; a few slots were USB 1.1, the other USB 2. the horn is recognized correctly?

Have you ever observed with a colleague who had such an external power supply? The USB port, if necessary, if I attach a device there now, I always get the message device can achieve higher performance.

Therefore, the board can not choose the high clock selbstatig. What can I do about it? Consequently, for 1066 operation, 533MHz memory clock can be run as an OC reserve. everything is already on AUTO.
Set 533 as Ramtakt in the BIOS!

Some manufacturers understand the possibility of the Ram with Fur 400Mhz but are still values ​​entered, the obediently the board stops, if no values ​​entered in the SPD.

The two bars plug each slot. Did I DRAM Frequenzy but only 1600Mhz displayed. CPU-Z under 'Memory' is at version of CPU-Z?
also not shown on Corsair link.

With motherboard perhaps something is forgotten? Furthermore, the bars are not displayed anything, everything is gray. It is in place 2 + 4.

The UEFI shows me the Corsair RAM and I can also put it on 3200Mhz via XMP. Do you also use the latest Corsair Venguence LED 3200 2x 8GB? I thank you. Under SPD me even AsRock Z270 Extreme4.

For help ware