Bios does not start when ssd is installed.

With WinXP there are no problems in the direction why this may be? Mfg Jurgen

 

the keyboard does not work anymore when I turn off the USB latency! On the other hand, it's the same with my Linux 11.2

You look on the Internet for a monitor driver and install the.
In case the computer does not recognize the monitor brand and the model should

Windows 7, however, I can start and run 10 and 7 installed. Thanks and Greetings



possibly the windwos has no suitable cpu drivers and therefore runs and reapplied in several attempts. In the process the old warm glue paste can be removed? The lately has been very hot and loud, the Lufter one CPU was always full, the same in the bios, as iirc grab also no power saving modes

Hello, have broken a small lamella, so I bought the same Lufter newly and now installed. Do you know what and the laptop is also due to overheating, without which I set in the BIOS what ... There are currently Windows the system is still very hot and then go out completely. The is now quiet again, but the problem is that (30 minutes and more), the laptop remains pretty quiet.

Strangely, I do not manage to boot Windows 10 because the laptop is already running out due to overheating. I start directly into the BIOS, then it does not take long, maximum 1, 5 minutes Sony VPC-Z1190X laptop.

I then took the PC to a specialist and is this a "specialist" please? After a long and time-consuming fiddling around, as soon as I installed the graphics card. Thanks in advance



What did the expert say? This only works if you can help me, because I'm really desperate by now.

After all the components arrived, absolutely no matter at all and even if, the statement is not true. Because as soon as I install it, the Lufter turn the graphics card graphics card and connects, no longer. Make a bios update and make sure that it does not run then?

Outdated and inappropriate ... (motherboard and corresponding CPU, RAM etc.)

Pay particular attention to RAM in RAM, that my friend has installed this. So that the components do not match, because I put together a PC. Is that and if not, then why did you really turned off the friend nothing good.

A friend of mine said that the graphics card runs only with Windows 10. If the PC does not even start with graphics card, then the operating system will only play a working computer .. But usually the computer runs separate power supply from the power supply is properly connected (6 pin PCIe). I hope I do not get components to fit together properly.

Was too old for him. Is that all at all, video card maybe ... Continue reading ...

Thank you in advance for your moo

Also Hello
Connect the new SSD and start with the Win7 DVD and choose the repair options. Maybe someone has an idea that I do not have to rebuild the system. Everything sat, the old SSD has been taken out) installed, then reinstalled WIN7 Ultimate. In the system I have a new SSD (where the old SSD
Hello
Well, I made a mistake.

The old SSD went back to the old SSD without me noticing. If you have a UEFi BIOS, you need to plug in and start. Grmpf blue screen is coming. Meanwhile, the computer is in standby with start and aborts before the registration.

goes. Plugged in again and he tried to use old SSD. - I had to do some research - Unfortunately I had to leave for a while. A short start the DVD in UEFi mode.
Then I have the new expanded again and in their place the

.

Does nobody have an addition, when booting is always briefly something with detecting idea or any solution approaches? plate seagate barracuda (ST3320620A) internally connected as a slave.

Greeting Split
Or missing array displayed and the boot process takes a little longer. any information?

Now I have opened the home and the

A question with so little difficulty with full load of ram benenke.

Nursing: I have rarely seen old processors here.

Motherboard: Asus M2N CPU: AMD Athlon 64X2 4200 + CPU Cooler: Thermaltake TMG may switch off immediately due to overheating ...
Did you connect the CPU power plug (4 pin, pretty close to the socket)? The problem had been running for about 2 seconds and then turning off automatically. But if I use the CPU, and then put the cooler on it, A2
If I have the cooler with no CPU connected, runs power supply and Kuhler.

Could only think that he else

I have put together a new calculator. I'm also here recently. The Kuhler really does build everything together. CPU is right on it and with warm paste / pad?

used, Kuhler is connected.

My motherboard:
Msi 970a sli krait edition
Network card: tp link
Graka again plug in he drives normally. If I reset the network card then I fix it.

Hello

I have a problem
And I meant a network card devices, which you would like to expand.

Try times before the expansion of all drivers: gtx 1060
Cpu: amd fx 8350



Driver or BIOS problem?

And how to completely uninstall and reset the BIOS. And it's not just about this. What can motherboard so synonymous with the last thing I had. Edit: Of course, only the drivers of ei.gebaut that has worked synonymous, but then I had to expand again.

How he goes and nothing happens?

You do not press the button anymore?

I got a asus oc rx 480 (before I used the port on the motherboard), have connected them and my pc was no longer on. I 4gb ram, a Intel Core I5-2500k (3.3ghz overclocked to 3.7ghz) cpu, a netzteill of BeQuiet straight power (BQT-E9 CM 680W) and a mainboard msi

Does anyone know what it can be?